Working towards a cleaner futureFASTflo(external)Installation Guide, Operation and Maintenance ManualThis manual must be kept with the appliance Octob
Caution• The water heater is designed for external installation only. Neverinstall it indoors or in a bathroom.• Consult with the customer concerning
INSTALLATION CLEARANCES116. Installation ClearancesItemDistance from combustibles• Maintain the following clearancesfrom both combustible andnon-combu
Illustration7. InstallationCheck4. Drill holes for the remaining four screws.5. Hang the unit again by the first screw, and theninsert and tighten the
GAS PIPING13Measuring Gas PressureIn order to check the gas supply pressure to the unit, atap is provided on the gas inlet. Remove the hex headphilip
9. Water PipingThis appliance is suitable for potable water. Do not use this appliance if any part has been underwater. Immediatelycall a qualified s
ELECTRICAL WIRING15Do not connect electrical power to the unit until all electrical wiring has been completed.Consult a qualified electricianfor the e
1. Remove the front cover of the heater (4 screws).2. Pass the remote controller cord through the wiringthroughway and into the unit.3. Connect the Y
COMMISSIONING17Handling after trial operation• In Freezing areas: If the unit will not be used immediately, close off all gas and water shutoffvalves,
Lighting InstructionsThis water heater does not have a pilot. It is equipped with an ignition device that automatically lightsthe burner.1. Read the
DIMENSIONS19412.DimensionsWHX56, LWHX56(unit: mm)LOWER WALL MOUNT BRACKETSCOLLGROUNDGASHOTWATER DRAIN VALVEWATER DRAIN VALVE(WATER FILTER)HOT WATER OU
SECTION XX • 2Reproduction of any information in this publication by any method is not permittedunless prior written approval has been obtained from
Wiring Diagram (WHX56, LWHX56)(VACANT CONNECTOR)BURNER THERMISTORBYPASS WATER FLOW SENSORMAIN WATERFLOW SENSORBLWGBLBLGWBLRRBKBKGAS VALVE UNITEARTHGAS
REMOE CONTROLLER INSTALLATION21NoteDo not connect power to the water heater before the remote controller has been properly installed.SETON / OFFSET(1)
11. Removing the transformer(1) Remove the 2 quick fasteners and removethe bypass pipe.14. ServicingImportant NotesTo ensure the continued efficient
DISASSEMBLY2382. Removing the electric board(1) Remove the locking screws at the topand bottom and ground screw, then pullboard out.3. Removing the ma
4 manifold locking screws.4. Removing the hot-water supply fan• Remove the electric board, manifold andintake gas pipe in advance.(1) Remove the 3 fan
DISASSEMBLY255. Removing the gas electromagneticvalve block• Remove the electric board and manifoldin advance.(1) Remove the gas electromagnetic valve
For Quick-discharge typeRemove the intake water pipe lockingscrew and 2 locking fasteners of thenon-return valve, then remove theintake water pipe an
DISASSEMBLY277. Removing the heat exchanger• Remove the electric board, manifold,mixing tube block and connectors inadvance.(1) Remove the 3 locking s
External outfitting LWHX56AD00100300200302307102100400900700801107001001207302503902202707207004007073007005000516.Servicing parts listsSERVICING PART
SERVICING PARTS LIST29External outfitting WHX56AD12627AKSSA-tes tnorF DA65XHW1001510LPAAPAA S gnikcap tnorF2002710LPAAPAA L gnikcap tnorF3001800
3CONTENTSPAGEGENERAL AND SAFETY INFORMATION 4SECTION 1 INCLUDED ACCESSORIES 7SECTION 2 OPTIONAL ACCESSORIES 7SECTION 3 QUICK CONNECT MULTI SYSTEM INST
Combustion unit and gas route WHX56AD10010912617317007011912507017312212312112017217207512417112111011611711711817117217517511211111511412707007307013
SERVICING PARTS LIST31Combustion unit and gas route WHX56AD12037PBSV-TES CAE tes ebut noitsubmoC00116057ABSV-TES KLD dor emalF1011210LKLDKLD )N rof(g
Hot-water feed route WHX56AD40142443342840248348440640240740840217340940647147051141141341043407345317242017245544344550941843445645643443146846845641
SERVICING PARTS LIST33Hot-water feed route WHX56ADThermal fuseHeat exchanger SETThermal fuse fastener(Rear side view))weiv edis thgiR()weiv edis tfeL(
Hot-water feed route WHX56AD LWHX5619317AKSSA-TES MJE regnahcxe taeH00418937ABSV-TES NHD esuf lamrehT1045300HDXCDXC renetsaf esuf lamrehT2042410A
SERVICING PARTS LIST35Electronic control unit WHX56AD703705700073710732070070714715717722070073721721733730731713711070070FGH701HFG712
Electronic control unit WHX56AD10587AHSSA-TES A-ELE esac yaleR0071130JELEELE DA ssenraH1071410JPRCPRC tiudnoc elbac pmaL3071410AKE
SERVICING PARTS LIST37Attached setRemote controller and Attached set WHX56AD803751752786788787Special part Special part no.<Special part>Owner&a
Remote controller and Attached set WHX56AD1310JAPQAPQ )ES(DA ydoB M8057-CR1571310AAPQAPQ )ES(DA ydob emarf desserD M257786 Oar plug 6X25 63390009
SPECIFICATIONS & PERFORMANCE39ItemGasConsumption (NET)Hot Water CapacityCapacity RangeTemperature Settings25$C Rise58$C Rise32 L/min.13 L/min.2.5
The Andrews Water Heater has been designed for usewith NATURAL GAS OR LPG and is manufactured to givean efficient, reliable and long service life.To e
Baxi Commercial DivisionWood Lane, Erdington, Birmingham B24 9QP Email: [email protected]:0845 070 1056Technical
GENERAL SAFETY INFORMATIONEFFECTIVENESS IN COMBATINGLEGIONELLAWater systems in buildings have been associated withoutbreaks of Legionnaires’ Disease,
Potential dangers from accidents during installation and use are divided into the following threecategories. Closely observe these warnings, they are
INCLUDED & OPTIONAL ACCESSORIES72. Optional AccessoriesThe accessories listed below are notincluded with the units, but may be necessaryfor instal
3. Quick Connect Multi System Installation• The Quick Connect Multi System allows the installation of two units together utilizing only the QuickConne
BEFORE INSTALLATION94Check the Gas• Check that the rating plate indicates the correct type of gas.Check that the gas supply line is sizedfor 62.3 kW(o
Kommentare zu diesen Handbüchern